Right Angle Design

BetaTest garment required

Jeans Block workspace

A drafting tool for a men's fitted tapered five-pocket jeans block. It is a beta, not a guarantee. You still have to sew a test garment and fit it before you cut real denim.

Before you start

  • This is a custom drafting beta. The numbers come from equations, not from a fitting room.
  • Sew a muslin or a cheap-denim test garment first. Write down what it tells you.
  • Nothing here is uploaded. Measurements live in this page only and clear when you refresh.
  • Fit review notes are saved in this browser so you can come back to them.

Units

Inches by default. Switching units changes the wording and numbers shown, never the size of your draft.

Which units should the form use?

Every measurement field has a number in it.

Consent, capture and calibrated review

Fitted clothing, hair secured, bare feet, full body visible. Level phone at waist height, fixed distance, plain background and even light. Photos remain in this tab; there is no silhouette extraction or vision analysis connected.

0/4 views present. Framing and pose require manual review; image presence does not prove calibration.

Marker: 3.94 in square. Print at 100%, check with a ruler. This simplified calibration form assumes square, equal front/side marker spans; asymmetric spans require a later full calibration worksheet.

Height has not been confirmed as measured (not guessed). Front view: marker not confirmed in the same plane as the body. Side view: marker not confirmed in the same plane as the body.

Measurement (in)Proposal / confidenceReview
Neck circumferenceManual measurement requirednone · manual measurement required — calibration not accepted.
Shoulder width (point to point)Manual measurement requirednone · manual measurement required — calibration not accepted.
Shoulder slope, left (°)Manual measurement requirednone · manual measurement required — calibration not accepted.
Shoulder slope, right (°)Manual measurement requirednone · manual measurement required — calibration not accepted.
High chestManual measurement requirednone · manual measurement required — calibration not accepted.
Chest / bustManual measurement requirednone · manual measurement required — calibration not accepted.
AbdomenManual measurement requirednone · manual measurement required — calibration not accepted.
WaistManual measurement requirednone · manual measurement required — calibration not accepted.
High hipManual measurement requirednone · manual measurement required — calibration not accepted.
Full hip / seatManual measurement requirednone · manual measurement required — calibration not accepted.
Front waist length (HPS over bust)Manual measurement requiredEstimated · none · manual measurement required — calibration not accepted.
Back waist lengthManual measurement requirednone · manual measurement required — calibration not accepted.
Armscye depthManual measurement requirednone · manual measurement required — calibration not accepted.
Armscye circumferenceManual measurement requirednone · manual measurement required — silhouettes cannot trace this curve.
Arm length, leftManual measurement requirednone · manual measurement required — calibration not accepted.
Arm length, rightManual measurement requirednone · manual measurement required — calibration not accepted.
Upper arm (bicep)Manual measurement requirednone · manual measurement required — calibration not accepted.
ElbowManual measurement requirednone · manual measurement required — calibration not accepted.
WristManual measurement requirednone · manual measurement required — calibration not accepted.
Crotch depth (standing, waist to crotch)Manual measurement requiredEstimated · none · manual measurement required — calibration not accepted.
Total rise / crotch length (front to back)Manual measurement requirednone · manual measurement required — silhouettes cannot trace this curve.
InseamManual measurement requirednone · manual measurement required — calibration not accepted.
Outseam (waist to floor)Manual measurement requirednone · manual measurement required — calibration not accepted.
ThighManual measurement requirednone · manual measurement required — calibration not accepted.
KneeManual measurement requirednone · manual measurement required — calibration not accepted.
CalfManual measurement requirednone · manual measurement required — calibration not accepted.
AnkleManual measurement requirednone · manual measurement required — calibration not accepted.
Waist height from floorManual measurement requirednone · manual measurement required — calibration not accepted.
Hip height from floorManual measurement requirednone · manual measurement required — calibration not accepted.
Knee height from floorManual measurement requirednone · manual measurement required — calibration not accepted.
Shoulder height difference (L − R)Manual measurement requirednone · manual measurement required — calibration not accepted.
Arm length difference (L − R)Manual measurement requirednone · manual measurement required — calibration not accepted.

Measurements

Use a cloth tape, stand relaxed, and wear what you would wear under jeans. Nothing here is saved after you close the page.

Fictional practice dataYou are drafting on the fictional male Medium preset. Replace it with your own numbers before cutting.
Where the jeans will sit. Tape snug, not tight.
About 3.94 in below the waist line, all the way round.
Around the fullest part, feet together.
Straight down the side, waist line to the fullest hip line.
Sit on a flat surface, tape from waist to the seat you are sitting on.
Waist line, down the front, to the crotch point.
Waist line, down the back, to the crotch point.
Around the fullest part of the thigh, weight even.
Around the kneecap, leg straight and relaxed.
Around the widest part of the calf.
Around the ankle bone. The finished hem can be wider.
Crotch seam to the floor, inside of the leg.
Waist line to the floor, outside of the leg.
Floor to the centre of the kneecap.
Floor to the waist line. Should match the outseam.
Bare feet, standing straight.

Total crotch length: 25.59 in — front rise plus back rise, worked out for you.

Fit-confidence report

0/16 manual values confirmed. Unconfirmed inputs may include fictional or estimated values. A number alone is not fit evidence; high hip, calf and inseam are reference inputs in this beta.

Body value (in)Origin / confidenceTape review
Natural waist32.99 inUnconfirmed · practice / entered value
High hip38.50 inUnconfirmed · practice / entered value
Full hip / seat40.98 inUnconfirmed · practice / entered value
Waist to hip depth7.87 inUnconfirmed · practice / entered value
Crotch depth (seated)10.00 inUnconfirmed · practice / entered value
Front rise10.83 inUnconfirmed · practice / entered value
Back rise14.76 inUnconfirmed · practice / entered value
Thigh22.99 inUnconfirmed · practice / entered value
Knee15.00 inUnconfirmed · practice / entered value
Calf14.02 inUnconfirmed · practice / entered value
Ankle12.99 inUnconfirmed · practice / entered value
Inseam32.99 inUnconfirmed · practice / entered value
Outseam42.99 inUnconfirmed · practice / entered value
Knee height17.01 inUnconfirmed · practice / entered value
Waist height42.99 inUnconfirmed · practice / entered value
Body height70.08 inUnconfirmed · practice / entered value

Design choices

These are decisions about the look, not about your body. Each one is written down separately in the summary.

Fit
Rise
Leg
Waistband
Fly
Pockets
Topstitching
Around the leg opening. Leave blank to let the style decide.
Cross-grain stretch. 0 for rigid denim.

Fabric

Denim changes the ease review, the needle, the seam finish and the cutting layout. It never changes your body measurements.

Fabric weight, not a length: 10 oz–14 oz is common denim.
58.00 in is common; selvedge is often 33.00 in.
The rest is usually elastane or polyester.
From your own wash test, not a guess.

Denim advice

Seam allowance
0.59 in
Hem allowance
1.57 in, double turned
Needle
Denim/jeans 100/16
Thread
Topstitch 40/3, two needles
Pressing
Press each seam open over a tailors ham before the next seam goes on.

Test the topstitching on a scrap of your actual denim before you stitch anything permanent.

Style variations

Straight and tapered draft now. Everything else stays visible so you can see what is coming, and stays switched off until it has been drafted, sewn, fitted and approved.

Drafting summary

Body measurements stay separate from every allowance. Nothing is quietly folded into a number.

All values in inches.
MeasurementBodyWearing easeDesignStretchAsymmetryFit fixFinished
Waist32.99 in0.98 in————33.98 in
High hip38.50 in1.77 in————40.28 in
Full hip / seat40.98 in1.97 in————42.95 in
Waist to hip depth7.87 in—————7.87 in
Crotch depth10.00 in—————10.00 in
Front rise10.83 in—————10.83 in
Back rise14.76 in—————14.76 in
Total crotch length25.59 in—————25.59 in
Thigh22.99 in2.36 in————25.35 in
Knee15.00 in1.57 in————16.57 in
Calf14.02 in1.38 in————15.39 in
Ankle12.99 in1.18 in————14.17 in
Inseam32.99 in—————32.99 in
Outseam42.99 in—————42.99 in
Knee height17.01 in—————17.01 in
Waist height42.99 in—————42.99 in
Body height70.08 in—————70.08 in

Seam allowance

0.59 in on every structural seam.

Hem allowance

1.57 in, double turned.

Shrinkage allowance

Fabric is prewashed, so no extra shrinkage allowance is added.

Fabric estimate

About 110.24 in at 57.99 in wide, laid out with a buffer.

How the block is calculated
  1. hip line below waist = waist to hip depth (else crotch depth x 0.78)
  2. front crotch extension = hip / 20
  3. back crotch extension = hip / 10
  4. front rise seam = measured front rise; centre waist height balances sampled crotch curve
  5. back rise seam = measured back rise; centre waist height balances sampled crotch curve
  6. front waist half before closing dart = waist / 4 + front dart
  7. back waist half before closing dart = waist / 4 + back dart
  8. front dart = clamp((hip - waist) / 4 x 0.15, 0.00 in, 0.79 in)
  9. back dart = clamp((hip - waist) / 4 x 0.45, 0.39 in, 1.57 in)
  10. leg centre = front crotch extension + (thigh / 2) / 2
  11. panel width at a level = leg circumference / 2
  12. knee line = outseam - knee height
  13. hem line = outseam
  14. waistband length = waist + 1.57 in

Pattern pieces

Curved front and back legs, shaped pocket and fly pieces, your selected waistband and a belt loop strip. Solid line is the cut line, dashed line is an curved stitch line.

Right Angle Design — Jeans Block BETA · TEST GARMENT REQUIRED · Fitted tapered — Available for beta fit testing Finished waist 33.98 in · hip 42.95 in · total rise 25.59 in · inseam 32.99 in Solid = offset cut line. Dashed = curved stitch line; check seam matching in the test garment. Print at 100% and measure the test square before cutting. Drafted from body + ease layers. Not a guaranteed bespoke fit. No yoke in this block. 1.97 in test square Measure this before cutting. If it is not 1.97 in, re-print at 100%. grain front dart intake 0.33 in; close before band hip line knee line pocket opening crotch point zip stop Front — cut 2 14.83 in x 42.99 in finished seam 0.59 in · hem 1.57 in grain back dart intake 1.01 in; close before band hip line knee line back pocket placement; check in fitting crotch point Back — cut 2 16.97 in x 44.81 in finished seam 0.59 in · hem 1.57 in grain Waistband — cut 1 + interfaced 35.55 in x 2.20 in finished seam 0.59 in · hem 1.57 in grain Waistband facing — cut 1 35.55 in x 2.20 in finished seam 0.59 in · hem 1.57 in grain fly fold / closure line Fly shield — cut 1 2.76 in x 7.87 in finished seam 0.59 in · hem 1.57 in grain fly fold / closure line Fly facing (right front) — cut 1 + interfaced 2.36 in x 7.87 in finished seam 0.59 in · hem 1.57 in grain opening / hem fold Front pocket lining — cut 2 9.06 in x 11.02 in finished seam 0.59 in · hem 1.57 in grain opening / hem fold Front pocket bag — cut 2 9.06 in x 11.02 in finished seam 0.59 in · hem 1.57 in grain opening / hem fold Front pocket facing — cut 2 4.72 in x 4.72 in finished seam 0.59 in · hem 1.57 in grain opening / hem fold Coin pocket — cut 1 3.74 in x 3.54 in finished seam 0.59 in · hem 1.57 in grain opening / hem fold Back patch pocket — cut 2 6.69 in x 7.48 in finished seam 0.59 in · hem 1.57 in grain Belt loop strip — cut 1 1.38 in x 18.70 in finished seam 0.59 in · hem 1.57 in

Beta reference draft: high hip, calf and inseam are not independently fit-constrained. Check seam matching, darts and waistband balance on the test garment; this is not verified bespoke fit.

Finished waist 33.98 in · Finished hip 42.95 in · Drafted total rise 25.59 in · Hem at 42.99 in from the waist · Fabric estimate 110.24 in at 57.99 in wide

Printing at 100%

  • Print the SVG at 100% with no scaling and no fit-to-page.
  • Measure the 1.97 in test square on the paper. If it is not 1.97 in, the print is wrong.
  • Use a large-format printer or a print service for this full-size sheet; no tiles or alignment marks are generated yet.
  • Letter and A4 tiled PDF: Coming Next. It is not generated yet, so it is not offered here.

Test jeans construction order

This is the order for a fit test, not the final fashion-house instruction course.

  1. Cut and mark every notch, dart and placement. Staystitch the waist and pocket openings.
  2. Test the chosen topstitch thread and tension on scrap denim with a jeans needle.
  3. Finish front pocket openings, join the lining and bags, then baste to the fronts.
  4. Hem and attach the coin pocket to the right pocket facing.
  5. Build the zipper fly: facing, zip and shield, then J-stitch.
  6. Close front and back darts and join centre seams. No yoke is included in this beta.
  7. Hem and attach back patch pockets while the backs are flat.
  8. Baste inseams, then outseams. Press each seam before the next operation.
  9. Interface the outer waistband, join to the facing, then baste to the waist.
  10. Fold and stitch the belt-loop strip, divide into five loops, then baste to the band.
  11. Fit the test garment before the final hem: check waist, seat, both legs and sitting comfort; record corrections.
  12. Mark the corrected length, double-turn the hem, press and test-sew. This is a fit test, not a final instruction course.

Because of your choices: Contoured band uses a conservative 0.47 in curve; confirm the contour on the test garment.

Fit review after the test garment

Sew the test garment, put it on, sit down, then fill this in. Notes are saved in this browser only.

Can you sit down without it cutting in?
Is there room across the buttocks, or is it flat?
Comfortable when you sit, or pressing?
Does the back waist drop when you bend?
Room to cross your legs?
Does the fabric bunch behind the knee?
Does the leg cling at the calf?
Where should the hem fall, with the shoes you plan to wear? Record any length correction in inches.
Which way do the lines point?
Stay sitting for two minutes and decide.
Not saved yet.

Muslin feedback and revision history

Check sitting comfort, waist, seat and drag lines above. Record alterations in inches. Earlier revisions never change. Photos stay in this tab and are excluded from saved summaries.

Jacket Block

One fitted jacket foundation, with separate denim and leather requirements. Both jackets are Coming Next.

Drafting and all downloads are off. This variation must be drafted, sewn, fitted and approved first.

Material requirements

  • Fabric weight (oz)
  • Cross-grain stretch
  • Recovery
  • Topstitching
  • Seam finish
  • Jeans needle
  • Zipper or snaps
  • Optional lining
  • Welt, patch or chest pockets

Workshop notes

  • Use a denim/jeans needle suited to the fabric weight.
  • Test topstitch thread and seam finish on scrap before sewing the jacket.

Drafting and all downloads are off. This variation must be drafted, sewn, fitted and approved first.

Material requirements

  • Hide type and thickness (inches)
  • Usable hide area (in²)
  • Grain and cutting direction
  • Leather needle
  • Longer stitch length (inches)
  • No-pin handling
  • Seam treatment
  • Lining
  • Zipper or snaps
  • Welt, patch or chest pockets
  • Reinforcement

Workshop notes

  • Use clips, not pins: holes in leather are permanent.
  • Test a leather needle and a longer stitch, around 0.12 in–0.16 in, on an offcut; adapt to hide thickness and machine limits.
  • Test leather-compatible seam treatment and reinforce closures and pocket openings. Avoid untested heat or adhesive.

Future choices: body length (inches), fit, collar, waistband or hem finish, sleeve and cuff, zipper or snaps, lining and welt, patch or chest pockets. No jacket pattern is generated yet.

Where the other patterns stand

Apron

Tested

Drafted, sewn and fitted. Still a sample pattern, not a production block.

Jeans

Beta drafting now

Straight and tapered legs draft and download. Every draft needs a test garment before denim.

Varsity jacket

In development

Sleeve and body blocks are being drafted. Nothing downloads yet.

Bridal / formal

Studio review coming soon

Not drafted. These need hand-fitting in the studio before anything is proposed.

No family is production-ready. A style only becomes available after it has been drafted, sewn, fitted and approved, and approval is recorded by a person, never by the software.